Cutting Tool Selection Guide
Parting and Grooving Inserts: Choosing TDC, TDJ and TDT for Steel and Stainless
Parting and grooving inserts for steel and stainless: TDC, TDJ, TDT, TDXU and MGGN — how to choose by operation, material and groove quality.
Parting and Grooving Inserts: Choosing TDC, TDJ and TDT for Steel and Stainless
Parting and grooving look like ordinary turning until the insert is inside the cut. A turning insert cuts on an open face; a grooving insert cuts in a slot barely wider than itself, and a parting insert cuts a workpiece off while buried to its full depth. Chips have nowhere easy to go, vibration has nowhere to hide, and the insert is doing its hardest work exactly where the operator can see it least. That is why parting and grooving inserts are a range of their own, not a turning insert used sideways.
CutStars lists its parting and grooving inserts in two entries: a general parting and grooving range for cutting off and grooving across materials, and a high-performance range built around five model families — TDC, TDJ, TDT, TDXU and MGGN. The choice between them is decided by the operation and the material, not by price alone.
Why grooving is a different cut
Three things make a groove harder than an open turning pass.
First, chip control. In a groove the chip is formed in a confined space, so a chip that curls wrong packs the slot, raises the cutting force and marks the groove walls. CutStars' grooving inserts use an optimised 3D groove form designed to control the chip, lower cutting resistance and cut vibration at the source — the groove shape is part of the cutting performance, not decoration.
Second, the substrate and coating are grooving-specific. A grooving insert needs wear resistance to hold the groove width and toughness to survive the interrupted entry and the side loads of a deep cut. The range is built on a grooving-specific substrate and coating that balances the two, so the insert keeps cutting reliably instead of wearing narrow or chipping at the corner.
Third, the operation decides the insert. Parting off, grooving a straight slot, cutting a wide groove, cutting across the face or finishing a groove surface are different jobs even when the material is the same. Picking the model from the operation first is what keeps a distributor from quoting a general insert into a job that needs a specialist one.
Choosing by model: TDC, TDJ, TDT, TDXU and MGGN
The high-performance range is organised by job, and the model letters are the shortcut:
- TDC — for steel. The steel grooving and parting choice. When the workpiece is steel and the job is a standard groove or part-off, TDC is the starting point.
- TDJ — for stainless steel. Stainless work-hardens and holds heat at the edge, so it gets its own model rather than a steel insert run harder. For stainless grooving and parting, start with TDJ.
- TDT — for wide grooves and transverse cutting. When the groove is wide, or the cut runs across the workpiece rather than along it, TDT is the model built for that geometry.
- TDXU — for end-face grooving. Grooving into the end face of a part is a different approach angle from grooving an outside diameter. TDXU is the model listed for face grooves.
- MGGN — for groove surface quality. When the groove surface itself is the requirement — a sealing face, a mating surface, a visible finish — MGGN is the model listed for excellent grooving surface quality.
For turning jobs on the same materials where the cut is open rather than grooved, see our guide to carbide CNC turning inserts — the P/M/K/N/S/H material groups and the GM and TF chipbreakers cover that choice.
What to send for an exact quotation
Grooving inserts are quoted from the job, not from a catalogue page. These are the five facts our product team asks for on every parting and grooving enquiry.
- The operation. Parting off, straight grooving, wide grooving, transverse cutting, end-face grooving, or a groove that must hold a surface finish — and which model family it points to.
- The material. Steel or stainless steel first; anything else needs a confirmed grade recommendation before quoting.
- The groove itself. Width, depth and tolerance, and whether the groove is on an outside diameter, an inside bore or an end face. Width and depth decide the insert size; the position decides the holder.
- The machine and holder. Lathe type, holder system and how the insert is clamped — a grooving insert that does not match its holder will not hold width, however good its groove form is.
- Batch size and how often the operation repeats. A one-off part-off and a production groove run are quoted differently, and repeat quantities change the stocking answer.
Send those five lines to info@cutstars.com or WhatsApp +86-151 1148 8179 and we will return an exact quotation for the inserts you run most. Distributors and importers can request the parting and grooving insert catalogue and the model list the same way. Enquiries are accepted by WhatsApp, the website form and email. For the milling that runs alongside these turned parts, see our solid carbide end mill range.
